mirror of
https://github.com/formtapez/ZigUP.git
synced 2025-02-23 09:34:50 +01:00
79 lines
5.6 KiB
Markdown
Executable File
79 lines
5.6 KiB
Markdown
Executable File
# ZigUP
|
||
CC2530 based multi-purpose ZigBee Relais, Switch, Sensor and Router
|
||
|
||
|
||
[Bottom side](https://raw.githubusercontent.com/formtapez/ZigUP/master/Pictures/bottom.jpg)
|
||
|
||
# Features
|
||
|
||
* [Small enough to fit under a normal lightswitch](https://raw.githubusercontent.com/formtapez/ZigUP/master/Pictures/size.jpg) in an european flush-mounted box ("Unterputzdose" - That´s the UP in ZigUP)
|
||
* integrated optional ZigBee Router functionality (extends the range of all your other devices)
|
||
* Powerful bistable relais for up to 10 amps load
|
||
* 2 Inputs for switches/buttons:
|
||
* Input "KEY" directly toggles the relais and outputs a ZigBee message
|
||
* Input "DIG" only outputs a ZigBee message - So your coordinator can decide if the relais has to be toggled or not.
|
||
* Input for 16 digital temperature (DS18B20) and 1 humidity sensors (DHT22/AM2302) (Measurements will be reported via ZigBee)
|
||
* Input for S0-Bus impulses from power-, water- or gas-meters. Count-Value will be reported via ZigBee)
|
||
* Output for one normal LED or up to 10 WS2812B/Neopixel RGB-LEDs (controllable via ZigBee)
|
||
* Analog input to measure voltages of up to 32 Volt. (Voltage will be reported via ZigBee)
|
||
* Fully equipped debug-port to allow CC Debugger flashing and packet sniffing
|
||
|
||
# Connection diagrams
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||
# Compilation
|
||
|
||
1. Get **Z-Stack Home 1.2.2a.44539** from http://www.ti.com/tool/Z-STACK-ARCHIVE
|
||
2. Get **IAR Embedded Workbench for 8051** from https://www.iar.com/iar-embedded-workbench (you can use the free trial version for one month)
|
||
3. Clone ZigUP source to **\Projects\zstack\HomeAutomation\ZigUP\\**
|
||
4. Start **\ZigUP\CC2530DB\ZigUP.eww** to load project in IAR
|
||
5. Choose between **Router** and **EndDevice** configuration
|
||
6. Edit **\Projects\zstack\Tools\CC2530DB\f8wConfig.cfg** to select the ZigBee channel your coordinator is using.
|
||
7. Compile
|
||
|
||
# Flashing with CC Debugger
|
||
1. Get **SmartRF Flash Programmer v1.12.8 (not v2.x!)** from https://www.ti.com/tool/flash-programmer
|
||
2. Connect CC Debugger to the Debug-Port of ZigUP with an 1:1 cable.
|
||
3. Select "Program CCxxxx..." and "System-on-Chip" tab
|
||
4. Load HEX-File and perform "Erase, program and verify" action
|
||
|
||
# Packet Sniffing using CC Debugger
|
||
As an alternative usage of this board, it can be used as a ZigBee packet-sniffer in combination with the CC Debugger.
|
||
1. Get **PACKET-SNIFFER v2.18.1 (not SNIFFER-2 v1.x!)** from https://www.ti.com/tool/PACKET-SNIFFER
|
||
2. Connect CC Debugger to the Debug-Port of ZigUP with an 1:1 cable.
|
||
3. Select protocol "IEEE 802.15.4/ZigBee" and click "Start"
|
||
4. Change radio channel and click "Start"
|
||
5. Re-flash ZigUP firmware when you are done, because it was replaced by a sniffer-firmware.
|
||
|
||
|
||
# Bill of Materials (BOM)
|
||
|
||
Qty | Value | Package | Parts | URL (exemplary supplier)
|
||
:--:|:----- |:------- |:------|:------------------------
|
||
5 | 100 | R0805 | R1, R3, R5, R9, R10 | https://uk.farnell.com/multicomp/mcwr08x1000ftl/res-100r-1-0-125w-0805-thick-film/dp/2447552
|
||
1 | 1k | R0805 | R8 | https://uk.farnell.com/multicomp/mcsr08x102-jtl/res-1k-5-0-125w-0805-ceramic/dp/2074338
|
||
3 | 10k | R0805 | R2, R4, R6 | https://uk.farnell.com/multicomp/mcwr08x1002ftl/res-10k-1-0-125w-0805-thick-film/dp/2447553
|
||
1 | 27k | R0805 | R7 | https://uk.farnell.com/multicomp/mcwr08x2702ftl/res-27k-1-0-125w-thick-film/dp/2447620
|
||
2 | 100n | C0805 | C4, C5 | https://uk.farnell.com/multicomp/mcu0805r104kct/cap-0-1-f-50v-10-x7r-0805/dp/9406387
|
||
3 | 10µ | C0805 | C1, C3, C6 | https://uk.farnell.com/murata/grm21br61e106ma73l/cap-10-f-25v-20-x5r-0805/dp/2611941
|
||
1 | 220µ/6V3/EEEFK0J221P | PANASONIC_D | C2 | https://uk.farnell.com/panasonic/eeefk0j221p/cap-220-f-6-3v-radial-smd/dp/1850086
|
||
8 | 4148 | 1206 | D1 - D8 | https://uk.farnell.com/taiwan-semiconductor/ts4148-rxg/diode-small-signal-75v-0-15a-1206/dp/2708388
|
||
2 | IRFML8244 | SOT23 | T1, T2 | https://uk.farnell.com/infineon/irfml8244trpbf/mosfet-n-ch-25v-5-7a-sot23/dp/1857298
|
||
1 | IRM-02-3.3 | IRM-02 | IC1 | https://uk.farnell.com/mean-well/irm-02-3-3/power-supply-ac-dc-3-3v-0-6a/dp/2815480
|
||
1 | CC2530 | E18-MS1-PCB | IC2 | https://www.aliexpress.com/item/-/32803052003.html
|
||
1 | DSP2A-L2-DC3V | DSP2A-L2 | K1 | https://uk.farnell.com/panasonic-electric-works/dsp2a-l2-dc3v/relay-dpst-no-250vac-30vdc-5a/dp/2095635
|
||
1 | MST 2.5A 250V | MST | F1 | https://uk.farnell.com/multicomp/mst-2-5a-250v/fuse-radial-slow-blow-2-5a/dp/1566104
|
||
1 | Phoenix 1792876 | PTS-3 | X1 | https://uk.farnell.com/phoenix-contact/1792876/terminal-block-wire-to-brd-3pos/dp/2072378
|
||
2 | TE 1-2834021-4 | MSC4 | X2, X3 | https://uk.farnell.com/te-connectivity/1-2834021-4/tb-wire-to-board-4pos-26-20awg/dp/2610379
|
||
1 | DEBUG | MA05-2 | X4 | https://uk.farnell.com/amphenol-icc-fci/67997-210hlf/connector-header-10pos-2row-2/dp/2886080
|
||
1 | PCB | FR4 | all | Use [Gerber files](https://github.com/formtapez/ZigUP/tree/master/Layout/Gerber) or contact me if you need a bare PCB
|
||
|