ESP32 Piano Note Detection System

A real-time piano note detection system implemented on ESP32 using I2S microphone input. This system can detect musical notes from C2 to C6 with adjustable sensitivity and visualization options.

Features

• Real-time audio processing using I2S microphone
• FFT-based frequency analysis
• Note detection from C2 (65.41 Hz) to C6 (1046.50 Hz)
• Dynamic threshold calibration
• Multiple note detection (up to 7 simultaneous notes)
• Harmonic filtering
• Real-time spectrum visualization
• Note timing and duration tracking
• Interactive Serial commands for system tuning

Hardware Requirements

• ESP32 development board
• I2S MEMS microphone (e.g., INMP441, SPH0645)
• USB connection for Serial monitoring

Pin Configuration

The system uses the following I2S pins by default (configurable in Config.h):

• SCK (Serial Clock): GPIO 8
• WS/LRC (Word Select/Left-Right Clock): GPIO 9
• SD (Serial Data): GPIO 10

Getting Started

1. Connect the I2S microphone to the ESP32 according to the pin configuration
2. Build and flash the project to your ESP32
3. Open a Serial monitor at 115200 baud
4. Follow the calibration process on first run

Serial Commands

The system can be controlled via Serial commands:

• h - Display help menu
• c - Start calibration process
• + - Increase sensitivity (threshold up)
• - - Decrease sensitivity (threshold down)
• s - Toggle spectrum visualization

Configuration Options

All system parameters can be adjusted in Config.h:

Audio Processing

• SAMPLE_RATE: 8000 Hz (good for frequencies up to 4kHz)
• BITS_PER_SAMPLE: 16-bit resolution
• SAMPLE_BUFFER_SIZE: 1024 samples
• FFT_SIZE: 1024 points

Note Detection

• NOTE_FREQ_C2: 65.41 Hz (lowest detectable note)
• NOTE_FREQ_C6: 1046.50 Hz (highest detectable note)
• FREQUENCY_TOLERANCE: 3.0 Hz
• MAX_SIMULTANEOUS_NOTES: 7
• MIN_NOTE_DURATION_MS: 50ms
• NOTE_RELEASE_TIME_MS: 100ms

Calibration

• CALIBRATION_DURATION_MS: 5000ms
• CALIBRATION_PEAK_PERCENTILE: 0.95 (95th percentile)

Visualization

The system provides two visualization modes:

1. Note Display:

Current Notes:
A4 (440.0 Hz, Magnitude: 2500, Duration: 250ms)
E5 (659.3 Hz, Magnitude: 1800, Duration: 150ms)

2. Spectrum Display (when enabled):

Frequency Spectrum:
0Hz    |▄▄▄▄▄
100Hz  |██████▄
200Hz  |▄▄▄
...

Performance Tuning

1. Start with calibration by pressing 'c' in a quiet environment
2. Play notes and observe the detection accuracy
3. Use '+' and '-' to adjust sensitivity if needed
4. Enable spectrum display with 's' to visualize frequency content
5. Adjust Config.h parameters if needed for your specific setup

Implementation Details

• Uses FFT for frequency analysis
• Implements peak detection with dynamic thresholding
• Filters out harmonics to prevent duplicate detections
• Tracks note timing and duration
• Uses ring buffer for real-time processing
• Calibration collects ambient noise profile

Troubleshooting

1. No notes detected:

   • Check microphone connection
   • Run calibration
   • Increase sensitivity with '+'
   • Verify audio input level in spectrum display

2. False detections:

   • Run calibration in a quiet environment
   • Decrease sensitivity with '-'
   • Adjust PEAK_RATIO_THRESHOLD in Config.h

3. Missing notes:

   • Check if notes are within C2-C6 range
   • Increase FREQUENCY_TOLERANCE
   • Decrease MIN_MAGNITUDE_THRESHOLD

Contributing

Contributions are welcome! Please read the contributing guidelines before submitting pull requests.

License

This project is licensed under the MIT License - see the LICENSE file for details.

Development Environment Setup

Prerequisites

• PlatformIO IDE (recommended) or Arduino IDE
• ESP32 board support package
• Required libraries:
  • arduino-audio-tools
  • arduino-audio-driver
  • WiFiManager
  • AsyncTCP
  • ESPAsyncWebServer
  • arduinoFFT

Building with PlatformIO

1. Clone the repository
2. Open the project in PlatformIO
3. Install dependencies:

   pio lib install
   

4. Build and upload:

   pio run -t upload
   

Memory Management

Memory Usage

• Program Memory: ~800KB
• RAM Usage: ~100KB
• DMA Buffers: 4 x 512 bytes
• FFT Working Buffer: 2048 bytes (1024 samples x 2 bytes)

Optimization Tips

• Adjust DMA_BUFFER_COUNT based on available RAM
• Reduce SAMPLE_BUFFER_SIZE for lower latency
• Use PSRAM if available for larger buffer sizes

Advanced Configuration

Task Management

• Audio processing runs on Core 1
• Main loop on Core 0
• Configurable priorities in Config.h

Audio Pipeline

1. I2S DMA Input
2. Sample Buffer Collection
3. FFT Processing
4. Peak Detection
5. Note Identification
6. Output Generation

Timing Parameters

• Audio Buffer Processing: ~8ms
• FFT Computation: ~5ms
• Note Detection: ~2ms
• Total Latency: ~15-20ms

Performance Optimization

CPU Usage

• Audio Processing: ~30% on Core 1
• Note Detection: ~20% on Core 1
• Visualization: ~10% on Core 0

Memory Optimization

1. Buffer Size Selection:
   • Larger buffers: Better frequency resolution
   • Smaller buffers: Lower latency
2. DMA Configuration:
   • More buffers: Better continuity
   • Fewer buffers: Lower memory usage

Frequency Analysis

• FFT Resolution: 7.8125 Hz (8000/1024)
• Frequency Bins: 512 (Nyquist limit)
• Useful Range: 65.41 Hz to 1046.50 Hz
• Window Function: Hamming

Technical Details

Microphone Specifications

• Supply Voltage: 3.3V
• Sampling Rate: 8kHz
• Bit Depth: 16-bit
• SNR: >65dB (typical)

Signal Processing

1. Pre-processing:
   • DC offset removal
   • Windowing function application
2. FFT Processing:
   • 1024-point real FFT
   • Magnitude calculation
3. Post-processing:
   • Peak detection
   • Harmonic filtering
   • Note matching

Calibration Process

1. Ambient Noise Collection (5 seconds)
2. Frequency Bin Analysis
3. Threshold Calculation:
   • Base threshold from 95th percentile
   • Per-bin noise floor mapping
4. Dynamic Adjustment

Error Handling

Common Issues

1. I2S Communication Errors:
   • Check pin connections
   • Verify I2S configuration
   • Monitor serial output for error codes
2. Memory Issues:
   • Watch heap fragmentation
   • Monitor stack usage
   • Check DMA buffer allocation

Error Recovery

• Automatic I2S reset on communication errors
• Dynamic threshold adjustment
• Watchdog timer protection

Project Structure

Core Components

1. AudioLevelTracker
   • Real-time audio level monitoring
   • Peak detection
   • Threshold management
2. NoteDetector
   • Frequency analysis
   • Note identification
   • Harmonic filtering
3. SpectrumVisualizer
   • Real-time spectrum display
   • Magnitude scaling
   • ASCII visualization

File Organization

• /src: Core implementation files
• /include: Header files and configurations
• /data: Additional resources
• /test: Unit tests